Development of a green and low-cost method to determine mercury content in sediments affected by oil spill on the Brazilian coast.

Tons of crude oil were found on the Brazilian coast in 2019, and studies assessing its chemical composition are still scarce. This study aimed to develop a new and simple technique of cold vapor generation using infrared irradiation coupled with atomic absorption spectrometry to determine mercury content in sediments contaminated by crude oil. Experimental conditions were evaluated, including formic acid concentration, reactor temperature, and carrier gas flow rate. The accuracy of the method was validated by comparison with mercury contents in a certified reference material (PACS-2). The detection limit was found to be 0.44 µg kg-1. The developed method was applied to determine the total mercury content in marine sediment samples collected from beaches in Ceará State. Mercury concentrations ranged from 0.41 to 0.95 mg kg-1. The proposed method is efficient, simple, low-cost, and adequate for its purpose.

Prediction of the marine spreading of low sulfur fuel oil using the long short-term memory model trained with three-phase numerical simulations.

In this study, we focus on the development and validation of a deep learning (long short-term memory, LSTM)-based algorithm to predict the accidental spreading of LSFO (low sulfur fuel oil) on the water surface. The data for the training was obtained by numerical simulations of artificial geometries with different configurations of islands and shorelines and wind speeds (2.0-8.0 m/s). For simulating the spread of oils in O(102) km scales, the volume of fluid and discrete phase models were adopted, and the kinematic variables of particle location, particle velocity, and water velocity were collected as input features for LSTM model. The predicted spreading pattern of LSFO matched well with the simulation (less than 10 % in terms of the mean absolute error for the untrained data). Finally, we applied the model to the Wakashio LSFO spill accident, considering actual geometry and weather information, which confirmed the practical feasibility of the present model.

Low dose phosphorus supplementation is conducive to remediation of heavily petroleum-contaminated soil-From the perspective of hydrocarbon removal and ecotoxicity risk control.

Biostimulation by supplementing of nitrogen and phosphorus nutrients is a common strategy for remediation of petroleum-polluted soils. However, the dosage influence of exogenous nitrogen or phosphorus on petroleum hydrocarbon removal and soil ecotoxicity and microbial function remain unclear. In this study, we compared the efficiencies of hydrocarbon degradation and ecotoxicity control by experiment conducted over addition of inorganic nitrogen or phosphorus at C/N ratio of 100/10, C/N/P ratio of 100/10/1, and C/P ratio of 100/1 in a heavily petroleum-contaminated loessal soil with 12,320 mg/kg of total petroleum hydrocarbon (TPH) content. A 90-day incubation study revealed that low-dose of phosphorus addition with the C/P ratio of 100/1 promoted hydrocarbon degradation and reduced soil ecotoxicity. Microbial community composition analysis suggested that phosphorus addition enriched hydrocarbon degrader Gordonia and Mycolicibacterium genus. The key enzymes EC 5.3.3.8, EC 6.2.1.20 and EC 6.4.1.1 which referred to degradation of long-chain hydrocarbons, unsaturated fatty acids and pyruvate metabolism were abundance by phosphorus supplementation. While nitrogen addition at C/N ratio of 100/10 or C/N/P ratio of 100/10/1 inhibited hydrocarbon degradation and exacerbated soil ecotoxicity due to promoting denitrification and coupling reactions with hydrocarbons. Our results suggested that low-dose phosphorus addition served as a favorable strategy to promote crude oil remediation and ecotoxicity risk control in heavily petroleum-contaminated soil. Hence, the application of suitable doses of exogenous biostimulants is an efficient approach to restore the ecological functions of organically contaminated soils.

Harpacticoid copepods expand the scope and provide family-level indicators of the Deepwater Horizon oil spill deep-sea impacts.

The Deepwater Horizon (DWH) blowout and oil spill began on April 20, 2010 in the northern Gulf of Mexico (NGOM) deep sea (1525 m). Previous studies documented an impacted area of deep-sea floor totaling 321 km2 and were based on taxonomy at the macrofauna family level and the meiofauna major taxonomic level. In the present study, finer taxonomic resolution of the meiofauna community was employed, specifically harpacticoid copepod family biodiversity. Severe or moderate impacts to harpacticoid family biodiversity were observed at 35 of 95 sampling stations, covering an estimated area of 2864 km2, 8.9 times greater impacted area than previously reported. Sensitive and tolerant harpacticoid families were observed in the impact zone. The present study greatly expands the understanding of DWH deep-sea impacts in 2010 and demonstrates that the harpacticoid family-level response is the most sensitive indicator (reported to date) of this oil spill pollution event.

Binary mixture of ionic liquid and span 80 for oil spill remediation: Synthesis and performance evaluation.

The synthesis of new surfactants helps to mitigate the environmental and financial effects of oil spills by providing efficient cleanup options. Herein, this study provides the development of a binary mixture of Span 80 and Choline myristate [Cho][Mys], a surface-active ionic liquid (SAIL) as green dispersant for oil spill remediation. The synergistic interaction at a 60:40 (w/w) ratio significantly lowered the critical micelle concentration (cmc) to 0.029 mM. Dispersion efficiency tests with Arab crude oil showed optimal performance at a 60:40 ratio of Span 80 and [Cho][Mys] (1:25 dispersant to oil ratio, v/v), achieving 81.16 % dispersion effectiveness in the baffled flask test. The binary mixture demonstrated superior emulsion stability (6 h) and the lowest interfacial tension (1.12 mN/m). Acute toxicity experiments revealed the dispersant's practical non-toxicity with an LC50 value of 600 mg/L. Overall, this environmentally benign surfactant combination shows promise as a safe and effective oil spill dispersant.

Influence of heavy Canadian crude oil on pristine freshwater boreal lake ecosystems in an experimental oil spill.

The overall impact of a crude oil spill into a pristine freshwater environment in Canada is largely unknown. To evaluate the impact on the native microbial community, a large-scale in situ model experimental spill was conducted to assess the potential role of the natural community to attenuate hydrocarbons. A small volume of conventional heavy crude oil (CHV) was introduced within contained mesocosm enclosures deployed on the shoreline of a freshwater lake. The oil was left to interact with the shoreline for 72 h and then free-floating oil was recovered using common oil spill response methods (i.e. freshwater flushing and capture on oleophilic absorptive media). Residual polycyclic aromatic hydrocarbon (PAH) concentrations returned to near preoiling concentrations within 2 months, while the microbial community composition across the water, soil, and sediment matrices of the enclosed oligotrophic freshwater ecosystems did not shift significantly over this period. Metagenomic analysis revealed key polycyclic aromatic and alkane degradation mechanisms also did not change in their relative abundance over the monitoring period. These trends suggest that for small spills (<2 l of oil per 15 m2 of surface freshwater), physical oil recovery reduces polycyclic aromatic hydrocarbon concentrations to levels tolerated by the native microbial community. Additionally, the native microbial community present in the monitored pristine freshwater ecosystem possesses the appropriate hydrocarbon degradation mechanisms without prior challenge by hydrocarbon substrates. This study corroborated trends found previously (Kharey et al. 2024) toward freshwater hydrocarbon degradation in an environmentally relevant scale and conditions on the tolerance of residual hydrocarbons in situ.

Native freshwater lake microbial community response to an in situ experimental dilbit spill.

With the increase in crude oil transport throughout Canada, the potential for spills into freshwater ecosystems has increased and additional research is needed in these sensitive environments. Large enclosures erected in a lake were used as mesocosms for this controlled experimental dilbit (diluted bitumen) spill under ambient environmental conditions. The microbial response to dilbit, the efficacy of standard remediation protocols on different shoreline types commonly found in Canadian freshwater lakes, including a testing of a shoreline washing agent were all evaluated. We found that the native microbial community did not undergo any significant shifts in composition after exposure to dilbit or the ensuing remediation treatments. Regardless of the treatment, sample type (soil, sediment, or water), or type of associated shoreline, the community remained relatively consistent over a 3-month monitoring period. Following this, metagenomic analysis of polycyclic aromatic and alkane hydrocarbon degradation mechanisms also showed that while many key genes identified in PAH and alkane biodegradation were present, their abundance did not change significantly over the course of the experiment. These results showed that the native microbial community present in a pristine freshwater lake has the prerequisite mechanisms for hydrocarbon degradation in place, and combined with standard remediation practices in use in Canada, has the genetic potential and resilience to potentially undertake bioremediation.

Modeling study on oil spill transport in the Great Lakes: The unignorable impact of ice cover.

The rise in oil trade and transportation has led to a continuous increase in the risk of oil spills, posing a serious worldwide concern. However, there is a lack of numerical models for predicting oil spill transport in freshwater, especially under icy conditions. To tackle this challenge, we developed a prediction system for oil with ice modeling by coupling the General NOAA Operational Modeling Environment (GNOME) model with the Great Lakes Operational Forecast System (GLOFS) model. Taking Lake Erie as a pilot study, we used observed drifter data to evaluate the performance of the coupled model. Additionally, we developed six hypothetical oil spill cases in Lake Erie, considering both with and without ice conditions during the freezing, stable, and melting seasons spanning from 2018 to 2022, to investigate the impacts of ice cover on oil spill processes. The results showed the effective performance of the coupled model system in capturing the movements of a deployed drifter. Through ensemble simulations, it was observed that the stable season with high-concentration ice had the most significant impact on limiting oil transport compared to the freezing and melting seasons, resulting in an oil-affected open water area of 49 km2 on day 5 with ice cover, while without ice cover it reached 183 km2. The stable season with high-concentration ice showed a notable reduction in the probability of oil presence in the risk map, whereas this reduction effect was less prominent during the freezing and melting seasons. Moreover, negative correlations between initial ice concentration and oil-affected open water area were consistent, especially on day 1 with a linear regression R-squared value of 0.94, potentially enabling rapid prediction. Overall, the coupled model system serves as a useful tool for simulating oil spills in the world's largest freshwater system, particularly under icy conditions, thus enhancing the formulation of effective emergency response strategies.

Assessment of spilled oil dispersion affected by dispersant: Characteristic, stability, and related mechanism.

Oil dispersion, a crucial process in oil transport, involves the detachment of oil droplets from slicks and their introduction into the water column, influencing subsequent oil migration and transformation. This study examines oil dispersion, considering characteristics, stability, and mechanisms, while evaluating the impact of dispersants and salinity. Results show the significant role of surfactant type in dispersants on oil dispersion characteristics, with anionic surfactants exhibiting higher sensitivity to salinity changes compared to nonionic surfactants. The dispersion efficiency varies with salinity, with anionic surfactants performing better in low salinity (<20‰) and nonionic surfactants showing superior performance at 30-35‰ salinities. Rheological analysis illustrates the breakup and coalescence of oil droplets within the shear rates of breaking waves. An increase in interfacial film rigidity impedes the coalescence of oil droplets, contributing to the dynamic stability of the oil-water hybrid system. The use of GM-2, a nonionic dispersant, results in the formation of a solid-like interface, characterized by increased elastic modulus, notably at 20‰ salinity. However, stable droplet size distribution (DSD) at 35‰ salinity for 60 h suggests droplets can remain dispersed in seawater. The enhancement of stability of oil dispersion is interpreted as the result of two mechanisms: stabilizing DSD and developing the strength of viscoelastic interfacial film. These findings offer insights into oil dispersion dynamics, highlighting the importance of surfactant selection and salinity in governing dispersion behavior, and elucidating mechanisms underlying dispersion stability.

Sustainable polyurethane for the remediation of oil spills: a review.

Catastrophic oil spill is one of the major issues to the environment. Various methods have been used to treat oil spillage including in situ burning, the use of skimmers, dispersants, bioremediation, dispersing agents, oil sorbents, and biological agents. Application of oil sorbent is one of the effective solutions in oil spill clean-up. Polymers are sustainable extraordinary materials for the treatment of oil spillage due to their special physicochemical characteristics such as high porosity, good hydrophobicity, and reusability. Polymers are modified using suitable chemical reagents and their hydrophobicity is enhanced, making them suitable for oil spill clean-up. The present manuscript is an attempt to summarize the study of chemical modifications done on a polymer polyurethane (PU) for achieving the desirable properties, for efficient oil spill clean-up. A patent analysis has been carried out for the leading countries, top inventors, leading assignees, trends of patent publications, citation analysis, and summary of granted patents in the area of the use of a polymer Polyurethane (PU) for oil spill clean-up.

Non-target analysis of crude oil photooxidation products at high latitudes and their biological effects.

With new oil and gas lease sales in high-latitude regions, there exists a need to better understand the chemical fate of spilled oil and its effects on biological life. To address this need, laboratory simulations of crude oil spills under sub-Arctic conditions were conducted using artificial seawater and exposure to solar irradiation to create Hydrocarbon Oxidation Products (HOPs). HOPs characterization and their biological effects were assessed using ultra high-performance liquid chromatography (UHPLC) with high resolution mass Orbitrap spectrometry and the aryl hydrocarbon receptor (AhR) chemically activated luciferase gene expression (CALUX) assay. Non-target UHPLC-Orbitrap mass spectrometry analysis identified 251 HOPs that were in greater abundance in light-exposed samples than dark controls. Oxidized polycyclic aromatic hydrocarbons were also detected, including phenanthrene quinone, anthraquinone, hydroxyanthraquinone, and 9-fluoreneone. The composition of HOPs were consistent with photo-products of alkylated two to four ring PAHs, primarily compounds between 1 and 3 aromatic rings and 1-3 oxygens. The HOP mixture formed during photochemical weathering of Cook Inlet crude oil induced greater AhR activity than parent petroleum products solubilized in dark controls, indicating that HOPs, as a complex mixture, may contribute to petroleum toxicity more than the parent petroleum compounds. These non-targeted approaches provide the most comprehensive analysis of hydrocarbon oxidation products to date, highlighting the diversity of the complex mixture resulting from the photooxidation of crude oil and the limitations of targeted analyses for adequately monitoring HOPs in the environment. Taken together, these data identify a critical "blind spot" in environmental monitoring and spill clean-up strategies as there is a diverse pool of HOPs that may negatively impact human and ecosystem health.

Impact of hydrocarbon extraction on heavy metal concentrations in lowland paca (Cuniculus paca) from the Peruvian Amazon.

Oil has been extracted from the Western Amazon since the 1920s, leading to severe environmental contamination due to frequent occurrence oil spills and the dumping of produced water. Local inhabitants, along with environmental and human rights organizations, have reported the adverse effects of oil-related pollution on their livelihoods and the ecosystems they depend on. Here, we study accumulation of oil-related heavy metals in wildlife, and its subsequent incorporation into the trophic chain. We analysed the concentration of 14 heavy metals (Cd, Cr, Hg, As, Ni, V, Ba, Se, Be, Fe, Cu, Zn, Mn, Al) in liver samples from 78 lowland pacas (Cuniculus paca) hunted for subsistence in an oil-polluted area from the northern Peruvian Amazon where oil has been extracted since the 1970s (n = 38), and two control areas, the Yavari-Mirín River basin (n = 20), and the Pucacuro River basin (n = 20). Pacas in the oil-polluted area have significantly higher concentrations of Cd (P < 0.01) and Ba (P < 0.0001) compared to those in control areas, suggesting bioaccumulation of oil-related pollution. Conversely, Se levels were significantly lower in the oil-polluted area (P < 0.0001), likely due to the sequestration of Se by other heavy metals, particularly Cd. Additionally, minor variations in other heavy metals, e.g., Fe and Zn, were observed in pacas from the oil-polluted area, whereas control areas showed higher concentrations of Ni and Cu. Mn and Al levels did not significantly differ between the study areas. These results underscore the impact of oil extraction on the absorption and assimilation of heavy metals in wildlife, point at oil activities as the source of the high and unsafe blood Cd levels reported for the indigenous population of the studied oil extraction area and raise concerns about the long-term health risks from oil extraction posed to local Indigenous People who rely on subsistence hunting.

Modelling fuel oil transformation on geographically different seacoasts and assessing their self-cleansing capacity.

The present paper considers the results of long-term (up to 17 years) in situ and laboratory research carried out on oiled French, Spanish, and Russian seacoasts. The objective of this research is to quantify the influence of geographical factors on the rates of natural transformation of the heavy fuel oil stranded ashore and to develop an empirical statistical model in order to evaluate the self-cleansing capacity of the coastal environment. In a number of field campaigns, 363 samples of weathered oil slicks and tar balls have been collected and analysed with the use of thin-layer chromatography combined with optical and gravimetric methods. The results obtained have been subjected to multiple nonlinear regression analyses. It has been shown that heavy fuel oil natural attenuation is more active in continental or estuarine environments influenced by nutrient-rich freshwater runoff and characterised by a higher number of sunny days, solar irradiation, and large temperature fluctuations. On the oceanic coasts, especially in sectors with low hydrodynamic energy, these processes take more time. The resulting model allows for the identification and mapping of the most vulnerable seacoasts, characterised by a low potential to degrade oil pollution. This information may be used in the contingency plans in order to optimise clean-up techniques and associated costs.

Unraveling the spectral and biochemical response of mangroves to oil spills and biotic stressors.

Mangroves are prone to biotic and abiotic stressors of natural and anthropogenic origin, of which oil pollution is one of the most harmful. Yet the response of mangrove species to acute and chronic oil exposure, as well as to other stressors, remains barely documented. In this study, a non-destructive, non-invasive approach based on field spectroscopy is proposed to unravel these responses. The approach relies on tracking alterations in foliar traits (pigments, sugars, phenols, and specific leaf area) from reflectance data in the 400-2400 nm spectral range. Three mangrove species hit by two of the most notorious oil spills in Brazilian history (1983 and 2019) and various biotic stressors, including grazing, parasitism, and fungal disease, were investigated through field spectroscopy and machine learning. This study reveals strong intra- and interspecific variability of mangrove's spectral and biochemical responses to oil pollution. Trees undergoing acute exposure to oil showed stronger alterations of foliar traits than the chronically exposed ones. Alterations induced by biotic stressors such as parasitism, disease, and grazing were successfully discriminated from those of oil for all species based on Linear Discriminant Analysis (Overall Accuracy ≥76.40% and Kappa ≥0.70). Leaf chlorophyll, phenol, and starch contents were identified as the most relevant traits in stressor discrimination. The study highlights that oil spills affect mangroves uniquely, both acutely and chronically, threatening their global conservation.

Effects of biochar immobilization of Serratia sp. F4 OR414381 on bioremediation of petroleum contamination and bacterial community composition in loess soil.

Petroleum hydrocarbons pose a significant threat to human health and the environment. Biochar has increasingly been utilized for soil remediation. This study investigated the potential of biochar immobilization using Serratia sp. F4 OR414381 for the remediation of petroleum-contaminated soil through a pot experiment conducted over 90 days. The treatments in this study, denoted as IMs (maize straw biochar-immobilized Serratia sp. F4), degraded 82.5% of the total petroleum hydrocarbons (TPH), 59.23% of the aromatic, and 90.1% of the saturated hydrocarbon fractions in the loess soils. During remediation, the soil pH values decreased from 8.76 to 7.33, and the oxidation-reduction potential (ORP) increased from 156 to 229 mV. The treatment-maintained soil nutrients of the IMs were 138.94 mg/kg of NO3- -N and 92.47 mg/kg of available phosphorus (AP), as well as 11.29% of moisture content. The activities of soil dehydrogenase (SDHA) and catalase (CAT) respectively increased by 14% and 15 times compared to the CK treatment. Three key petroleum hydrocarbon degradation genes, including CYP450, AJ025, and xylX were upregulated following IMs treatment. Microbial community analysis revealed that a substantial microbial population of 1.01E+ 09 cells/g soil and oil-degrading bacteria such as Salinimicrobium, Saccharibacteria_genera_incertae_sedis, and Brevundimonas were the dominant genera in IMs treatment. This suggests that the biochar immobilized on Serratia sp. F4 OR414381 improves soil physicochemical properties and enhances interactions among microbial populations, presenting a promising and environmentally friendly approach for the stable and efficient remediation of petroleum-contaminated loess soil.

Socio-economic baseline for oil-impacted communities in Ogoniland: towards a restoration framework in Niger Delta, Nigeria.

This study documents the socio-economic baselines in selected oil-impacted communities prior to the commencement of the Ogoni clean-up and restoration project. Adopting mixed approach consisting of semi-structured interviews, focus group discussions (FGDs), key informant interviews (KIIs), and household surveys, we surveyed the pre-remediation socio-economic conditions in the Ogoniland communities between July 2018 and March 2019. Results indicated that almost all respondents (99.6%) agreed that the smell of petroleum products or crude oil was evident in the air they breathed even as there were visible black particles (soot) in the respondents' nostrils, on their clothes, and in water. The respondents described the ambient air as smoky and choked with an offensive smell. The household waters were smelly, brownish, or oily, and most respondents (76%) cannot afford to treat their water. Forty-two percent of the respondents who relied on fishing and farming for a living sought for alternative means of subsistence and acknowledged that oil pollution caused stunted growth and low crop yield. The majority of respondents (91%) reported falling fish catches, while the fish caught smell and taste of oil, lowering their market value and posing a potential health risk to consumers. It is evident that oil pollution has impacted the socio-ecological values and sustainable livelihood in Ogoniland. This study provides baseline data for monitoring post-remediation socio-economic improvements in Ogoniland. It also highlights areas of urgent intervention to improve livelihood, and access to basic amenities (e.g., potable drinking water), waste management infrastructure, and statutory policy changes for sustainable development in Ogoniland.

The impact of chronic and acute problems on sea turtles: The consequences of the oil spill and ingestion of anthropogenic debris on the tropical semi-arid coast of Ceará, Brazil.

Sea turtle mortality is often related to materials that reach the coast from different anthropic activities worldwide. This study aimed to investigate whether sea turtle mortality was related to older marine problems, such as solid waste, or one of the largest oil spill accidents on the Brazilian coast, that occurred in 2019. We posed three questions: 1) Are there solid residues in the digestive tract samples, and which typology is the most abundant? 2) Can meso­ and macro-waste marine pollutants cause mortality? 3) Is the dark material found really oil? A total of 25 gastrointestinal content (GC) samples were obtained, of which 22 ingested waste of anthropogenic origin and 18 were necropsied. These 22 samples were obtained during or after the 2019 oil spill, of which 17 specimens were affected, making it possible to suggest oil ingestion with the cause of death in the animals that could be necropsied. Macroscopic data showed that the most abundant solid waste was plastic (76.05 %), followed by fabrics (12.18 %) and oil-like materials. However, chemical data confirmed only three specimens with oil levels ranging from remnants to high. It was possible to infer possible causes of death in 16 of the total 18 necropsied cases: Most deaths were due to respiratory arrest (62.5 %), followed by pulmonary edema (12.5 %), cachexia syndrome (12.5 %), circulatory shock (6.25 %), and head trauma (6.25 %), which may have been caused by contact with solid waste, oil, or both. The study showed that not all dark material found in the GCs of turtles killed in oiled areas is truly oil, and in this sense, a chemical analysis step to prove the evidence of oil must be added to international protocols.

[The application of molecular biology-based microbial remediation technologies in petroleum polluted environments].

Owing to human activities and industrial production, petroleum pollution has become a serious environmental issue. Microbial remediation technology, characterized by its eco-friendly characteristics, has drawn significant attention in petroleum pollution remediation. The application of molecular biology technology has led to a drastic revolution in microbial remediation technology, providing resources for the development of highly efficient degrading agents. However, limitations such as the lack of precision in species annotation and the limited detection sensitivity still exist. Other microbial remediation technologies also have substantial potential in enhancing the degradation efficiency of petroleum pollutants and reducing their environmental harm, especially biosurfactants and bio-stimulants, which offer relatively shorter remediation periods and lower costs, promising large-scale application in the future. Moreover, the combination of molecular biology and other microbial remediation technologies may become an effective tool for petroleum pollutant degradation. This review summarized the application of molecular biology methods in petroleum polluted environments, reviewed the recent research progress on microbial remediation techniques for petroleum-contaminated sites, discussed the remediation effects of these microbial remediation techniques, and proposed the future development direction of microbial remediation technology.

Surface active dicationic ionic liquids as green oil spill dispersants.

The utilization of chemical dispersants as a way of mitigating of oil spills in marine eco-system has been extensively documented worldwide. Hence, in this research we have successfully synthesized two amphiphilic asymmetric Dicaionic Ionic Liquids (DILs). The efficacy of these synthesized DILs as dispersants was assessed using the baffled flask test (BFT). The results indicated a dispersant effectiveness ranging from 47.98 % to 79.76 % for the dispersion of heavy crude oil across various temperature ranges (10-30 °C). These dispersant-to-oil ratios (DOR) were maintained at 3: 100 (V%), showcasing promising dispersant capabilities for mitigating heavy crude oil spills. Additionally, acute toxicity tests conducted on Nile tilapia and Oreochromis niloticus have demonstrated the relatively low toxicity of the IL-dispersants, with Lethal Concentration 50 (LC50) values exceeding 100 ppm after 96 h. This suggests a practically slight toxic effect on the tested fish. In summary, the newly developed IL-dispersants are considered to be conducive to environmentally benign oil spill remediation.

Techniques for hazing and deterring birds during an oil spill.

Preventing wildlife from becoming oiled is the priority in an oiled wildlife response. This is achieved through diverting spilled oil away from wildlife, or hazing, deterring, or excluding wildlife from oiled areas. This paper undertakes an international review of techniques deployed for hazing and deterring birds, the taxa most affected, during oil spills. Using these techniques as a baseline it then compares what techniques are used in New Zealand at airports, in agriculture, and at waste management facilities, to assess what could readily be deployed in New Zealand during oil spills, as currently there are few options planned for. As international literature suggests, the best technique is to use a variety of methods for targeted species to reduce habituation. This review highlights international practices that could be tested and implemented, to allow for planning for effective hazing and deterrence practices in New Zealand.